Ricoh Aficio MP 2500 Facsimile Reference Manual Download | Manualshive

Page: 51 / 204

background image

Placing Originals

41

1

Detecting Blank Sheet

Upon completion of the first page scanning, an alarm sounds if the page is nearly
blank.

Important

❒

The blank sheet-detecting function works only when an original is scanned
using the ARDF.

❒

The blank sheet-detecting function is ineffective for second and subsequent
pages.

This function notifies you if an original is placed wrong side down on the scan-
ner. When this happens, a message appears for a few seconds. The message dif-
fers depending on the number of pages to be scanned and transmission mode.
• When sending a document using Immediate Transmission or when all pages

have been scanned in Memory Transmission:

• When some pages are left unscanned in Parallel Memory Transmission or

Memory Transmission:

Note

❒

Even if a near blank sheet is detected, it is transmitted as normal.

❒

You can turn this function on or off with the User Parameter (switch 11, bit 2)
in the Fax Features menu.

❒

To cancel scanning if a blank sheet is detected, press the

{

Clear/Stop

}

key.

Reference

“Fax Features”, General Settings Guide

«
...
49
50
51
52
53
...
»

Summary of Contents for Aficio MP 2500













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 2500

Brand: idp Pages: 88

Brand: Canon Pages: 521

Brand: Canon Pages: 456

Brand: Microplex Pages: 135

Brand: Tektronix Pages: 42

VarioPrint 4110

Brand: Oce Pages: 216

Brand: Star Micronics Pages: 127

Brand: EcLine Pages: 72

Brand: Panduit Pages: 39

Brand: Muratec Pages: 188

Brand: Muratec Pages: 364

Magicolor 2 Desklaser

Brand: MINOLTA-QMS Pages: 4

Brand: Oki Pages: 105

Brand: Samsung Pages: 2

Brand: Samsung Pages: 18

Brand: Samsung Pages: 6

Brand: Samsung Pages: 6

Brand: Samsung Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands