Ricoh Aficio CL5000 Maintenance Manual Download

Page: 58 / 80

Cleaning and Adjusting the Printer

Cleaning the Paper Feed Roller and the
Friction Pad

CAUTION:

Papers other than the plain paper
produce more paper dust. Clean the
paper feed roller and the friction pad
to avoid paper misfeeds.

Cleaning the Paper Feed
Roller (for Tray 1) and the
Friction Pad

AAAA

Pull out Tray 1 slowly while lift-
ing it up a little.

The paper feed roller (for Tray 1) is
installed as shown in the illustra-
tion.

The friction pad is installed as
shown in the illustration.

BBBB

Lower the base panel by pushing
"Push". When paper is loaded in
the tray, push down on the paper.

•

The inside of the machine be-
comes very hot. Do not touch the
parts with a label indicating "

(means hot surface). Touching
"

" (means hot surface) could

result in a burn.

ZESH436J

ZESH437J

ZESH550J

ZESH470J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands