Ricoh Aficio CL5000 Maintenance Manual Download

Page: 35 / 80

Development Unit Type 5000 Black/Color

JJJJ

Close the left cover of the printer
by pushing the fasteners (

)

while holding the cover (

KKKK

Turn on the power switch.

"Please Wait" appears on the panel
display, and then initial adjust-
ments begin. Please wait until it
stops for approximately three and
a half minutes per color.

Important

❒

Do not turn off the power
switch when adjustments are
being made to avoid a printer
malfunction.

Printing the Test Page

AAAA

Press

{{{{

Menu

}}}}

Print the sheet for checking the col-
or condition to confirm the devel-
o p m e n t u n i t s a r e p r o p e r l y
installed.

"Menu" appears on the panel dis-
play.

BBBB

Press

{{{{U

U}}}}

{{{{T

T}}}}

to show "Main-

tenance" on the panel display,
and then press

{{{{

Enter #

}}}}

"Maintenance" appears on the pan-
el display.

CCCC

Press

{{{{U

U}}}}

{{{{T

T}}}}

to show

"Devp.Unit Check" on the panel
display, and then press

{{{{

Enter #

}}}}

The message appears on the panel
display.

Please Wait

ZESH018J

Menu:

Maintenance

Devp.Unit Check

Press # to test

print Devp. Unit

On Line

Job Reset

Escape

Enter

Form Feed

Power

Error

Data In

ZDJS001N

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands