Ricoh Aficio CL5000 Maintenance Manual Download

Page: 33 / 80

Development Unit Type 5000 Black/Color

From the top, the development
units are installed in the order of
black, yellow, cyan, and magenta.

CCCC

Detach the connectors from the
development units from the top
to the bottom by pressing the
sides of the connectors.

Note

❒

When replacing only the black
development unit, detach the
top connector only. The other
connectors do not have to be de-
tached.

DDDD

Remove the development unit of
desired color by lifting it first as
shown in the illustration (

→

The illustration shows how to re-
move the black development unit.
The procedure is the same for all
four colors.

Important

❒

Be sure to hold the unit with
both hands, and then pull it
slowly.

EEEE

Hold the development unit, and
then shake it about 10 times.

Important

❒

Hold the unit with the roller fac-
ing down.

❒

Do not add shocks to the unit.

❒

If you do not shake the unit
well, it may take longer for the
initial adjustments when turned
on.

ZESH403J

ZESH410J

ZESH411J

ZESHE414J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands