Ricoh Aficio CL5000 Maintenance Manual Download

Page: 30 / 80

Replacing Consumables and Maintenance Kit

QQQQ

If the Duplex Unit is installed,
close it.

RRRR

Close the Bypass Tray.

SSSS

Close the front cover slowly by
pushing the two areas on the left
and right.

TTTT

Turn on the power switch.

Note

❒

If you hear a noise while print-
ing after replacing the fuser oil
unit, the seals

and

may not

have been removed. Go back to
step

to confirm that the seals

are removed.

UUUU

Perform the maintenance reset.

When "Replace Fuser Oil Unit"
appears on the panel display

Press and hold

{{{{

Escape

}}}}

for

over five seconds. The message
disappears and maintenance
reset start automatically.

When "Replace Fuser Oil Unit
soon" appears on the panel display

Press

{{{{

Menu

}}}}

"Menu" appears on the panel
display.

Press

{{{{U

U}}}}

{{{{T

T}}}}

to show

"Maintenance" on the panel
display, and then press

{{{{

Enter

}}}}

"Maintenance" appears on the
panel display.

ZESH405J

ZESH406J

Replace

Fuser Oil Unit

Menu:

Maintenance

On Line

Job Reset

Escape

Enter

Form Feed

Power

Error

Data In

ZDJS001N

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands