Ricoh Aficio CL5000 Maintenance Manual Download

Page: 39 / 80

Fusing Unit Type 5000/Friction Pad/Paper Feed Roller

Replacing the friction pad and
the paper feed roller (for Tray 1)

AAAA

Turn off the printer power.

Important

❒

To prevent a burn, be sure to
wait about 30 minutes after the
power is turned off until the
fusing unit cools down before
touching the fusing unit.

BBBB

Pull out Tray 1 slowly while lift-
ing it up a little.

The friction pad is installed as
shown in the illustration.

The paper feed roller (for Tray 1) is
installed as shown in the illustra-
tion.

CCCC

Lower the base panel by pushing
"Push". When paper is loaded in
the tray, push down on the paper.

DDDD

When paper is loaded in the tray,
remove them.

EEEE

Remove the stopper (

), and then

release the bar that is holding the
paper feed roller by pushing to-
wards back (

ZESH436J

ZESH550J

ZESH437J

ZESH470J

ZESH438J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands