Ricoh Aficio CL5000 Maintenance Manual Download

Page: 38 / 80

Replacing Consumables and Maintenance Kit

Fusing Unit Type 5000/Friction Pad/Paper
Feed Roller

CAUTION:

Replace all of the paper feed roller,
friction pad and fusing unit when the
following message appears on the
panel display.

Note

❒

When replacing the fusing unit, re-
place the paper feed roller (for
Tray 1) and the friction pad as well.

❒

Replace the friction pad and the
paper feed roller before replacing
the fusing unit.

Check the contents of the box for the
following items:

❖

Fusing Unit

❖

Friction Pad

❖

Paper Feed Roller

❖

Gloves

❖

Fitting

❖

Maintenance Guide

•

The inside of the machine be-
comes very hot. Do not touch the
parts with a label indicating "

(means hot surface). Touching
"

" (means hot surface) could

result in a burn.

•

The fusing unit becomes very
hot. When installing the new fus-
ing unit, turn off the printer and
wait about 30 minutes. After that,
install the new fusing unit. Not
waiting for the unit to cool down
can result in a burn.

•

Do not pull out the fusing unit
forcefully. It may cause the unit
to fall and result in an injury.

•

When touching the fusing unit,
do not touch any areas other
than the handle as it may cause
a burn.

Replace

Fusing Unit

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands