Ricoh Aficio CL5000 Maintenance Manual Download

Page: 28 / 80

Replacing Consumables and Maintenance Kit

IIII

Hold the green part in the center
of the fuser oil unit, and then re-
move it from the fusing unit by
lifting it in the directions shown
(

→

Important

❒

Be careful not to let oil on the
fuser oil unit get in contact with
your hands or clothes.

JJJJ

Put the removed fuser oil unit in
the bag supplied.

KKKK

Take out the new fuser oil unit
from the bag. Remove the cover-
ing paper, the seals, and then the
fitting.

Remove the seal

by shaking

it to pull.

Note

❒

If you cannot remove it easi-
ly, pull it out with a little
force.

Remove the seal

slowly by

turning the fuser oil unit.

Remove the fitting.

Important

❒

Be sure to remove the seals to
avoid a printer malfunction.

❒

Be sure to remove the seal

first, and then remove the
seal

to avoid an oil leak.

❒

Be sure to put the fuser oil
unit in a stable and level
place to avoid an oil leak.

❒

Oil is on the seals and fusing
oil roller after removal. Be
careful not to get it on your
hands or clothes.

ZESH404J

ZESH804J

ZESH055J

ZESH805J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands