Ricoh Aficio CL5000 Maintenance Manual Download

Page: 37 / 80

Development Unit Type 5000 Black/Color

HHHH

Pull out the development unit
partially (approximately 30mm

) by lifting it first as shown in

the illustration.

The illustration shows how to pull
out the black development unit.
The procedure is the same for all
four colors.

Important

❒

Be sure to hold the unit with
both hands, and then pull it
slowly.

IIII

Push the development unit slow-
ly until it stops.

JJJJ

Confirm the label for the color,
and then confirm that the unit is
securely fit in the stoppers.

When there is a white line showing
at the stoppers, reinsert the units.

KKKK

Repeat steps

AAAA

DDDD

to print the

sheet for checking the color again
and re-check the print quality.

ZESTE050E

ZESTE060E

ZESH650J

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands