Ricoh Aficio CL5000 Maintenance Manual Download

Page: 45 / 80

Fusing Unit Type 5000/Friction Pad/Paper Feed Roller

TTTT

Turn on the power switch.

UUUU

Make a setting from the control
panel.

When Two Messages Appear on
the Panel Display

When the following messages
appear on the panel display,
follow the steps in the instruc-
tion manual that is provided
with the fusing unit.

When Only One Message
Appears on the Panel Display

Press

{{{{

Menu

}}}}

"Menu" appears on the panel
display.

Press

{{{{U

U}}}}

{{{{T

T}}}}

to display

"Maintenance", and then press

{{{{

Enter #

}}}}

Press

{{{{U

U}}}}

{{{{T

T}}}}

to display

"Maint. Reset", and then press

{{{{

Enter #

}}}}

Press

{{{{U

U}}}}

{{{{T

T}}}}

to display

"Fusing Unit", and then press

{{{{

Enter #

}}}}

The following message appears.

Press

{{{{

Enter #

}}}}

. Wait for a few

seconds.

Press

{{{{

On Line

}}}}

"Ready" appears on the panel
display.

Replace

Fusing Unit

See Instructions

before replacing

Replace

Fusing Unit

On Line

Job Reset

Escape

Enter

Form Feed

Power

Error

Data In

ZDJS001N

Menu:

Maintenance

Maintenance:

Maint. Reset

Maint. Reset:

Fusing Unit

Fusing Unit:

Press # to Reset

Ready

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands