Ricoh Aficio CL5000 Maintenance Manual Download | Manualshive

Page: 57 / 80

background image

53

3. Cleaning and Adjusting the

Printer

Cautions to Take When Cleaning

R

WARNING:

R

CAUTION:

Clean the printer periodically to maintain fine printing.
Dry wipe the exterior with a soft cloth. If dry wiping is not enough, wipe with a
soft, wet cloth that is wrung out well. If you still cannot remove the stain or
grime, use a neutral detergent, and then wipe over with a well-wrung wet cloth,
dry wipe, and let it dry.

Important

❒

To avoid deformation, discoloration, or cracking, do not use volatile chemi-
cals, such as benzine and thinner, or spray insecticide on the printer.

❒

If there is dust or grime inside the printer, wipe with a clean, dry cloth.

•

Do not remove any covers or screws other than those specified in this
manual. Some parts of the machine are at a high voltage and could
give you an electric shock. Also, if the machine has laser systems, di-
rect (or indirect) reflected eye contact with the laser beam may cause
serious eye damage. When the machine needs to be checked, adjust-
ed, or repaired, contact your service representative.

•

Do not take apart or attempt any modifications to this machine. There
is a risk of fire, electric shock, explosion or loss of sight. If the machine
has laser systems, there is a risk of serious eye damage.

•

When removing misfed paper, do not touch the fusing unit because it could
be very hot.

«
...
55
56
57
58
59
...
»

Summary of Contents for Aficio CL5000

















































































Reviews:

No comments

Related manuals for Aficio CL5000

PIXMA MX882 Series

Brand: Canon Pages: 34

Brand: Canon Pages: 4

Brand: Canon Pages: 913

Laser Class 700 Series

Brand: Canon Pages: 30

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 108

PIXMA MX860 series

Brand: Canon Pages: 9

imagePROGRAF iPF9400

Brand: Canon Pages: 8

PIXMA MX860 series

Brand: Canon Pages: 93

Brand: Canon Pages: 20

Brand: Canon Pages: 30

Brand: Canon Pages: 2

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 4

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 16

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 170

Brand: Samsung Pages: 165

Brand: Xerox Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands