Ricoh Aficio CL5000 Maintenance Manual Download

Page: 56 / 80

Replacing Consumables and Maintenance Kit

VVVV

If the Duplex Unit is installed,
close it.

WWWW

Close the Bypass Tray.

XXXX

Close the front cover slowly by
pushing the two areas on the left
and right.

YYYY

Turn on the power switch.

The following message appears on
the panel display. The printer
starts calibration. Please wait until
it stops.

Important

❒

Do not turn off the power
switch while calibration to
avoid a printer malfunction.

❒

When one of the following mes-
sages appears on the panel dis-
play, waste toner bottle 1 may
not be installed properly. Go
back to step

to remove waste

toner bottle 1, and then go to
step

to set them properly.

❒

If the photoconductor unit is
not installed properly, reinstall
from step

. If you cannot in-

stall it properly even after rein-
stallation, contact your sales or
service representative.

Calibrating...

ZESH405J

ZESH406J

Reset Waste

Toner1 Correctly

Reset PCU

Correctly

Summary of Contents for Aficio CL5000

















































































Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands

Ricoh Aficio CL5000, Maintenance Manual

Search results

Summary of Contents for Aficio CL5000

Reviews:

Related manuals for Aficio CL5000

Brands by name

Popular brands