background image

 

 

52 

ENGLISH 

GB 

 
Both water inlet and drain pipe connections are 
3/4”. To know which attachment to use (both 3/4”), 
simply follow the indications in the figure (the 
same label should be found near the water supply 
connections). 
 

 If the water has a high mineral salt content 

(i.e. if it is too hard), to ensure long and efficient 
life to the exchanger we suggest you install a 
water softener at the water inlet. 
 

 

 
Even if the pressure valve has been calibrated 
before leaving the factory, after having connected 
the machine to the water supply and turned on the 
any cocks installed, check for water leaks from the 
drain when the machine is at a standstill. In case 
of a leak, adjust the pressure valve until the leak 
stops. 

8.5.  Remote condensing unit 

!

 When installing a remote condensing unit, 

the same precautions must be taken as for the 
installation of the machine with an integrated 
condensing unit. In particular, it is important to 
respect the electric installation rules, the fire-
prevention rules and to keep in mind that under 
certain circumstances coolant gas may be 
released into the environment (it must be possible 
to air the room). 
 

 Performance is guaranteed for remote unit 

installations up to a distance of 10 m and with an 
insulated intake line (insulation must be at least 
13 mm thick). 
 
The recommended pipes are given in the 
attachments. 
 
 

 Both the condensing unit and the coolant 

circuit are under pressure using nitrogen therefore 
the seal of the circuits can be checked when 
turning on the cocks. 
 
After having connected the delivery and intake 
pipes and having created a vacuum and then 
loaded the pipes, make sure that the welded parts 
are hermetically sealed and that there are no 
leaks. 
 
The gas load must be checked through the gas 
conduit indicator located on the condensing unit. 
 
For installations on the same level or different 
level follow the indications in the figure. 
In particular, if the remote unit is installed higher, 
a siphon is created at every departure/arrival or 
re-ascent, while if the unit is installed lower no 
siphon is necessary. 

 

Summary of Contents for Comfort 1011

























































Reviews: