Renesas Single-Chip Microcomputer SH7203 Hardware Manual Download Page 11

Page: 11 / 1622

Rev. 0.50 May 18, 2006 Page xi of xxx

5.2.4

Manual Reset ........................................................................................................ 108

5.3

Address Errors ................................................................................................................... 109

5.3.1

Address Error Sources .......................................................................................... 109

5.3.2

Address Error Exception Handling ....................................................................... 110

5.4

Register Bank Errors.......................................................................................................... 111

5.4.1

5.4.2

5.5

Interrupts ............................................................................................................................ 112

5.5.1

Interrupt Sources................................................................................................... 112

5.5.2

Interrupt Priority Level ......................................................................................... 113

5.5.3

Interrupt Exception Handling................................................................................ 114

5.6

Exceptions Triggered by Instructions ................................................................................ 115

5.6.1

Types of Exceptions Triggered by Instructions .................................................... 115

5.6.2

Trap Instructions ................................................................................................... 116

5.6.3

Slot Illegal Instructions ......................................................................................... 116

5.6.4

General Illegal Instructions................................................................................... 117

5.6.5

Integer Division Instructions................................................................................. 117

5.6.6

Floating Point Operation Instructions ................................................................... 118

5.7

When Exception Sources Are Not Accepted ..................................................................... 119

5.8

Stack Status after Exception Handling Ends...................................................................... 120

5.9

Usage Notes ....................................................................................................................... 122

5.9.1

Value of Stack Pointer (SP) .................................................................................. 122

5.9.2

Value of Vector Base Register (VBR) .................................................................. 122

5.9.3

Address Errors Caused by Stacking of Address Error Exception Handling ......... 122

Section 6 Interrupt Controller (INTC) ...............................................................123

6.1

Features .............................................................................................................................. 123

6.2

Input/Output Pins ............................................................................................................... 125

6.3

Register Descriptions ......................................................................................................... 126

6.3.1

Interrupt Priority Registers 01, 02, 05 to 17 (IPR01, IPR02, IPR05 to IPR17) .... 127

6.3.2

Interrupt Control Register 0 (ICR0)...................................................................... 129

6.3.3

Interrupt Control Register 1 (ICR1)...................................................................... 130

6.3.4

Interrupt Control Register 2 (ICR2)...................................................................... 131

6.3.5

IRQ Interrupt Request Register (IRQRR)............................................................. 132

6.3.6

PINT Interrupt Enable Register (PINTER)........................................................... 134

6.3.7

PINT Interrupt Request Register (PIRR) .............................................................. 135

6.3.8

Bank Control Register (IBCR).............................................................................. 136

6.3.9

Bank Number Register (IBNR)............................................................................. 137

6.4

Interrupt Sources................................................................................................................ 139

6.4.1

NMI Interrupt........................................................................................................ 139

Summary of Contents for Single-Chip Microcomputer SH7203























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Single-Chip Microcomputer SH7203

Reviews:

Related manuals for Single-Chip Microcomputer SH7203

Brands by name

Popular brands

Renesas Single-Chip Microcomputer SH7203, Hardware Manual

Search results

Summary of Contents for Single-Chip Microcomputer SH7203

Reviews:

Related manuals for Single-Chip Microcomputer SH7203

Brands by name

Popular brands