M16C/62P Group (M16C/62P, M16C/62PT)
25. Differences Depending on Manufacturing Period
Rev.2.41
Jan 10, 2006
Page 383 of 390
REJ09B0185-0241
25. Differences Depending on Manufacturing Period
Table 25.1 and Table 25.2 list the precautions are applicable or not applicable every chip version of M16C/62P flash
and ROM external versions. Contact separately about the mask ROM version.
√
: Applies
−
: Dose not apply
Table 25.1
Technical Update Applicable Table of M16C/62P Flash and ROM External Versions (1)
Precaution
Chip Version
TECHNICAL
UPDATE
A
B
C
Ensure that RESET must hold valid-low state during power-on.
When using a reset IC, use a CMOS type IC. When using an
open-drain type reset IC, insert a capacitor between the reset
input and VSS. Adjust the R-C time constant between the
capacitor and pull-up resistor at least 10 times longer than the
VCC rising time.
√
−
−
If UART0 or UART1 are used as a slave in the I
2
C mode, P6_1
or P6_5 are placed in a high-impedance state. P6_1 or P6_5
cannot be used as an output port even if the PD6_1 or PD6_5 bits
in the PD6 register are set to “1” (output mode). Therefore, set
the PD6_1 or PD6_5 bits to “0” (Input mode).
√
−
−
TN-M16C-100-0309
Do not enter wait mode when the main clock or on-chip oscillator
clock is selected as the CPU clock of which division is set by the
CM06 bit in the CM0 register, and the CM16 and CM17 bits in the
CM1 register.
√
−
−
TN-M16C-108-0309
Precaution 1.1
The CM05 bit in the CM0 register is set to “0” (main clock
oscillation) and the CM02 bit is set to “1” (peripheral function
clock stops in wait mode).
√
−
−
TN-M16C-108-0309
Precaution 1.2
Do not generate an NMI interrupt after entering mode.
√
−
−
TN-M16C-108-0309
Precaution 1.3
Do not generate a voltage detection interrupt after entering
mode.
√
−
−
TN-M16C-108-0309
Precaution 1.4
I/O ports (P0 to P5) will be indeterminate until internal power
supply is stable, such as when the power is turned on, if “H” is
applied to the CNVSS pin and “L” to the RESET pin while internal
power supply is unstable.
√
√
√
TN-M16C-114-0310
Precaution 1.1
I/O ports (P6 to P14) will be indeterminate until internal power
supply is stable, such as when the power is turned on, if “H” is
applied to the CNVSS pin and “L” to the RESET pin while internal
power supply is unstable.
√
−
−
TN-M16C-114-0310
Precaution 1.1
When the RESET pin is “L” in boot mode (apply “H” to the
CNVSS pin and P5_0 (CE), and “L” to the P5_5 (EPM)), internal
pull-up is enabled for P10_0 to P10_3, P11_0 to P11_7, P12_5
to P12_7, P13_0 to P13_7, P14_0 and P14_1 and so become “H”
level.
√
−
−
TN-M16C-114-0310
Precaution 1.2
P0_0 to P0_7 and P1_0 to P1_7 may become indeterminate
when P8_4 is “H” and the RESET pin is “L” in boot mode (apply
“H” to the CNVSS pin and P5_0 (CE), and “L” to P5_5 (EPM)).
P0_0 to P0_7 and P1_0 to P1_7 are in a high impedance state
when the RESET pin and P8_4 are “L”.
√
√
√
TN-M16C-114-0310
Precaution 1.3
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655