
M16C/62P Group (M16C/62P, M16C/62PT)
17. Serial Interface
Rev.2.41
Jan 10, 2006
Page 189 of 390
REJ09B0185-0241
17.1.1
Clock Synchronous Serial I/O Mode
The clock synchronous serial I/O mode uses a transfer clock to transmit and receive data. Table 17.1 lists the
Clock Synchronous Serial I/O Mode Specifications. Table 17.2 lists the Registers to Be Used and Settings in
Clock Synchronous Serial I/O Mode.
NOTES:
1. When an external clock is selected, the conditions must be met while if the CKPOL bit in the UiC0 register = 0
(transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock),
the external clock is in the high state; if the CKPOL bit in the UiC0 register = 1 (transmit data output at the rising
edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state.
2. If an overrun error occurs, the receive data of UiRB register will be indeterminate. The IR bit in the SiRIC
register does not change.
3. The U0IRS and U1IRS bits respectively are the bits 0 and 1 in the UCON register; the U2IRS bit is the bit 4 in
the U2C1 register.
Table 17.1
Clock Synchronous Serial I/O Mode Specifications
Item
Specification
Transfer Data Format
Transfer data length: 8 bits
Transfer Clock
• CKDIR bit in the UiMR(i=0 to 2) register = 0 (internal clock) : fj/ (2(n+1))
fj = f1SIO, f2SIO, f8SIO, f32SIO n: Setting value of UiBRG register 00h to FFh
• CKDIR bit = 1 (external clock) : Input from CLKi pin
Transmission, Reception
Control
Selectable from CTS function, RTS function or CTS/RTS function disable
Transmission Start
Condition
Before transmission can start, meet the following requirements
(1)
• The TE bit in the UiC1 register = 1 (transmission enabled)
• The TI bit in the UiC1 register = 0 (data present in UiTB register)
• If CTS function is selected, input on the CTSi pin = L
Reception Start Condition
Before reception can start, meet the following requirements
(1)
• The RE bit in the UiC1 register = 1 (reception enabled)
• The TE bit in the UiC1 register = 1 (transmission enabled)
• The TI bit in the UiC1 register = 0 (data present in the UiTB register)
Interrupt Request
Generation Timing
For transmission, one of the following conditions can be selected
• The UiIRS bit
(3)
= 0 (transmit buffer empty): when transferring data from the UiTB
register to the UARTi transmit register (at start of transmission)
• The UiIRS bit =1 (transfer completed): when the serial interface finished sending data
from the UARTi transmit register
For reception
• When transferring data from the UARTi receive register to the UiRB register (at
completion of reception)
Error Detection
Overrun error
(2)
This error occurs if the serial interface started receiving the next data before reading
the UiRB register and received the 7th bit of the next data
Select Function
• CLK polarity selection
Transfer data input/output can be chosen to occur synchronously with the rising or the
falling edge of the transfer clock
• LSB first, MSB first selection
Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can
be selected
• Continuous receive mode selection
Reception is enabled immediately by reading the UiRB register
• Switching serial data logic
This function reverses the logic value of the transmit/receive data
• Transfer clock output from multiple pins selection (UART1)
The output pin can be selected in a program from two UART1 transfer clock pins that
have been set
• Separate CTS/RTS pins (UART0)
CTS0 and RTS0 are input/output from separate pins
http://www.xinpian.net
提供单片机解密、IC解密、芯片解密业务
010-62245566 13810019655