Raven AutoBoom UltraGlide XT Installation Manual Download Page 75

Page: 75 / 78

Index

Manual No. 016-0171-122 Rev. E

Electrical

Safety

Hydraulic

Fittings

Safety

Hydraulic System Installation

Building the UltraGlide XT Valve Assembly

Hydraulic Schematic

Installing Fittings in the UltraGlide XT Valve

Installing the Cylinder Hoses

Installing the Pressure and Tank Hoses

Installing the UltraGlide XT Cylinder

Mounting the AutoBoom Valve (If Applicable)

Mounting the UltraGlide XT Valve Assembly

Important Safety Information

Electrical

Hydraulics

Installation

Model Year 2012 & Newer - RG Series

Installing the Valve Harness

Connecting the Valve Harness to the

Sensors - UltraGlide Installed

on the Machine (If
Applicable)

Introduction

AutoBoom UltraGlide and UltraGlide XT Kit

Contents

Model Year 2009 6
Model Years 2010-2011 11

Updates

Point of Reference

Preparing for Installation

Recommendations

Replacement Parts

Sensors

Valves

Sensor Installation

Installing the Rotary Sensor

Installing the Sensors

UltraGlide Installed on the Machine

Mounting the Boom Sensors

UltraGlide Not Installed on the Machine 38

Installing the Boom Sensors

Installing the Center Sensor

Installing the Center Sensors

39, 40

Installing the UltraGlide XT Boom Sensors

Boom Sensor Mounting Locations 37

Startup Procedures

Calibrating the AutoBoom UltraGlide XT System

Verifying the AutoBoom Hydraulic System

Installation

Verifying the UltraGlide XT Wiring

Tools Needed

UltraGlide

Install

Wiring

Connecting the Harness Cable to the

Controller Cable

Wiring Installation

Installing the UltraGlide XT Auxiliary Sensor Cable

Node & Harness Installation

Model Year 2009

Connecting the CAN/Power Cables -

Gen I Cable Only

Connecting the Harness Cable to the

Implement Extension Tee -
Gen II Cable Only

Connecting the Harness Cable to the

Sensors

Connecting the Harness Cabpe to the

Powr Cable - Gen I Cable
Only

Connecting the Harness to the Boom

Function Controls

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 75 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: