Raven AutoBoom UltraGlide XT Installation Manual Download Page 58

Page: 58 / 78

HAPTER

Viper Pro Installation & Operation Manual

MODEL YEAR 2009 NODE AND HARNESS INSTALLATION

INSTALL THE ULTRAGLIDE XT NODE

FIGURE 16. Installed AutoBoom Node

1. Mount the AutoBoom node (P/N 063-0130-023) on the mounting bracket (P/N 107-0171-619) using three

3/8”-16 UNC x 1-1/4” hex bolts (P/N 311-0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

2. Secure the mounting bracket to the machine’s center rack using two 2-9/16” W x 3-1/2” L x 3/8” thread U-bolts

(P/N 107-0171-616) and four 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

NOTE:

Position the node so that the cable connectors face down or to the side. One of the six numbered

direction arrows on the node must be oriented in the direction of vehicle travel, one arrow pointing

straight up, and two arrows parallel to the ground.

3. Insert the large, rectangular node connectors on the harness cable (P/N 115-0230-095 or 115-0230-116) into the

correct ports of the AutoBoom node.

4. Tighten the bolt on the node connectors to secure the connections.

CONNECT THE HARNESS TO THE BOOM FUNCTION CONTROLS

FIGURE 17. Harness Cabling Connections

1. Locate the LEFT PRESS and RIGHT PRESS connectors on the valve harness (P/N 115-0230-095 or 115-0230-116).

Left Prop

Left Solenoid

Right Prop Port

Right Solenoid

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 58 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: