manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 50 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 50

C

HAPTER

 5

46

Viper Pro Installation & Operation Manual

4. Remove the bulkhead locking nut from the connector and place the connector back into the node mounting 

box.

FIGURE 2. Node Harness Installed on Bulkhead (View from Inside Box)

5. Install the large, 31-pin connector from the UltraGlide XT node harness (P/N 115-0230-109) through the open 

hole in the bulkhead from which the SYS BLKHD 5 connector was removed.

6. Thread the bulkhead locking nut that was removed from the SYS BLKHD 5 connector onto the 31-pin connector 

to secure it.

FIGURE 3. Connector to be Removed

7. Disconnect the RAVEN CAN TO AUTOBOOM connector from the front-center of the node box, near the latch 

pin.

8. Locate the CAN connector on the node harness and connect it to the open connection.

31-Pin Connector 

from UltraGlide 

XT Node Harness

Disconnected SYS 

BLKHD 5 

Connector

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments