Raven AutoBoom UltraGlide XT Installation Manual Download Page 77

Page: 77 / 78

Raven Industries will not assume any expense or liability for repairs

made outside our facilities without written consent. Raven Industries

is not responsible for damage to any associated equipment or

products and will not be liable for loss of profit, labor, or other

damages. The obligation of this warranty is in lieu of all other

warranties, expressed or implied, and no person or organization is

authorized to assume any liability for Raven Industries.

Damages caused by normal wear and tear, misuse, abuse,

neglect, accident, or improper installation and maintenance are

not covered by this warranty.

What is not Covered by this Warranty?

Upon confirmation of the warranty claim, Raven Industries will (at our

discretion) repair or replace the defective product and pay for the

standard return freight, regardless of the inbound shipping method.

Expedited freight is available at the customer’s expense.

What Will Raven Industries Do?

Bring the defective part and proof of purchase to your Raven dealer.

If the dealer approves the warranty claim, the dealer will process the

claim and send it to Raven Industries for final approval. The freight cost

to Raven Industries will be the customer’s responsibility. The Return

Materials Authorization (RMA) number must appear on the box and all

documentation (including proof of purchase) must be included inside

the box to be sent to Raven Industries.

How Can I Get Service?

Raven Applied Technology products are covered by this warranty for 12

months from the date of retail sale. In no case will the Limited Warranty

period exceed 24 months from the date the product was issued by

Raven Industries Applied Technology Division. This warranty coverage

applies only to the original owner and is non-transferable.

How Long is the Coverage Period?

This warranty covers all defects in workmanship or materials in your

Raven Applied Technology Division product under normal use,

maintenance, and service when used for intended purpose.

What Does this Warranty Cover?

Limited Warranty

016-0171-537 Rev. A, E19889

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 77 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: