Raven AutoBoom UltraGlide XT Installation Manual Download Page 4

Page: 4 / 78

Table of Contents

Viper Pro Installation & Operation Manual

Connect the Sensor Cables ..............................................................................................................................................

Install the Power/CAN Cable ...........................................................................................................................................

Model Year 2009 Node and Harness Installation ....................................................................

Install the UltraGlide XT Node ........................................................................................................................................

Connect the Harness to the Boom Function Controls ...........................................................................................

Install the Center Rack Control .......................................................................................................................................

Connect the Harness Cable to the Sensors ...............................................................................................................

Connect the Harness Cable to the Power Cable - Gen I Cable Only ...............................................................

Connect the CAN/Power Cables - Gen I Cable Only ..............................................................................................

Connect the Power Leads - Gen I Cable Only ...........................................................................................................

Connect the Harness Cable to the Implement Extension Tee - Gen II Cable Only ....................................

Install the UltraGlide XT Auxiliary Sensor Cable

.....................................................................

Wiring Diagram ........................................................................................................................

2009 Wiring Schematic ......................................................................................................................................................

2010-2011 Wiring Schematic ..........................................................................................................................................

2012 & Newer Wiring Schematic ..................................................................................................................................

Chapter 6

Startup Procedures

..............................................................................................

Verify the AutoBoom Hydraulic System Installation .................................................................

Verify the UltraGlide XT Wiring ................................................................................................

Calibrate the AutoBoom UltraGlide XT System .......................................................................

Chapter 7

Replacement Parts

...............................................................................................

Valve .......................................................................................................................................

Sensors ...................................................................................................................................

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 4 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: