manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 5 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 5

CHAPTER

1

Manual No. 016-0171-122 Rev. E

1

CHAPTER 1

IMPORTANT SAFETY 

INFORMATION

Read this manual and the operation and safety instructions included with your implement and/or controller 

carefully before installing the AutoBoom™ system.
• Follow all safety information presented within this manual.
• If you require assistance with any portion of the installation or service of your Raven equipment, contact your 

local Raven dealer for support.

• Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good 

condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety 

labels, contact your local Raven dealer.

When operating the machine after installing AutoBoom, observe the following safety measures:
• Be alert and aware of surroundings.
• Do not operate AutoBoom or any agricultural equipment while under the influence of alcohol or an illegal 

substance.

• Remain in the operator’s position in the machine at all times when AutoBoom is engaged.
• Disable AutoBoom when exiting from the operator’s seat and machine.
• Do not drive the machine with AutoBoom enabled on any public road.
• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling 

AutoBoom when the safe working distance has been diminished.

• Ensure AutoBoom is disabled prior to starting any maintenance work on AutoBoom or the machine.

• When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear, in 

case a hose has not been properly tightened.

• The machine must remain stationary and switched off, with the booms unfolded, during installation or 

maintenance.

NOTICE

 

WARNING

 

CAUTION

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments