manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 61 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 61

5

Manual No. 016-0171-122 Rev. E

57

WIRING INSTALLATION

3. Install the LEFT INNER SENSOR connector on the 40’ sensor cable (P/N 115-0171-602).
4. Connect the other end of the 40’ sensor cable to the left inner sensor.
5. Install the RIGHT OUTER SENSOR connector on the 70’ sensor cable.
6. Connect the other end of the 70’ installed sensor cable to the right outer sensor.
7. Install the RIGHT INNER SENSOR connector on the 40’ sensor cable.
8. Connect the other end of the installed 40’ sensor cable to the right inner sensor.
9. Connect the CENTER US SENSOR connector to the center sensor (P/N 063-0130-014) cable connection.

CONNECT THE HARNESS CABLE TO THE POWER CABLE - GEN I CABLE ONLY

1. Route the harness cable (P/N 115-0230-116) toward the machine’s cab.
2. Connect the harness cable to the power cable (P/N 115-0230-007).
3. Tighten the connector screw cap to secure the connection.

CONNECT THE CAN/POWER CABLES - GEN I CABLE ONLY

FIGURE 20. Existing CAN Terminator

1. Locate the CAN cable under the cat-walk on the right side of the machine.
• If a CAN passive terminator is on the CAN connector as shown in Figure 20 on page 57:

a. Remove the CAN terminator.
b. Connect the male CAN connection on the power cable (P/N 115-0230-007) to the connector from which 

the terminator was removed.

c. Install the terminator on the CAN connection of the harness cable (P/N 115-0230-116) coming from the 

AutoBoom node.

• If the CAN connector does not have a CAN passive terminator and another CAN cable is already connected:

a. Disconnect the existing CAN termination.
b. Connect the CAN connection from the power cable (P/N 115-0230-007).into the connector from which 

the other CAN cable was unplugged.

c. Reroute the disconnected CAN cable to the CAN connection near the AutoBoom node on the harness 

cable (P/N 115-0230-116).

d. Loop and tie-off any excess cable.

2. Locate the CAN power connector as shown in Figure 20 on page 57.
• If the CAN power connector is not is use:

a. Remove the dust cap from the power connection.

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments