manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 70 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 70

C

HAPTER

 6

66

Viper Pro Installation & Operation Manual

3. Press the button to manually rotate the boom counterclockwise via the UltraGlide system, verifying that the 

boom rotates counterclockwise as viewed from behind the machine.

NOTE:

If the boom rotates in the wrong direction, the UltraGlide XT valve harness corrections may need to 

be changed. Refer to Install the Valve Harness section on page 48 for further information.

NOTE:

If there are issues with the AutoBoom system, turn off the machine and correct them immediately. For 

additional assistance, refer to the AutoBoom UltraGlide XT Calibration & Operation Manual 

(P/N 016-0130-062) or contact your local Raven dealer.

CALIBRATE THE AUTOBOOM ULTRAGLIDE XT SYSTEM

Refer to the AutoBoom UltraGlide XT Calibration & Operation Manual (P/N 016-0130-062) for instructions on 

calibrating the system, adjusting system settings, and system operation.

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments