manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 28 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 28

C

HAPTER

 3

24

Viper Pro Installation & Operation Manual

MOUNT THE AUTOBOOM VALVE (IF APPLICABLE)

FIGURE 1. Machine’s Hydraulic Valve Before AutoBoom Installation

1. Strip the factory paint from the top of the machine’s hydraulic valve using a chemical approved for paint 

removal.

IMPORTANT:

Do not scrape the paint from the machine’s hydraulic valve. Scraping the paint may cause damage to the 

valve.

2. Remove the hydraulic test port fitting and Allen plugs from the machine’s hydraulic valve.

NOTE:

The test port fitting will be installed on the AutoBoom hydraulic valve later in the procedure. Protect 

the test port fitting from dust and debris to avoid contamination of the hydraulic system.

3. Clean the remaining paint from the machine’s hydraulic valve, taking care to prevent paint chips from entering 

the open hydraulic ports.

4. Install 9/16” ID Buna-N O-rings (P/N 219-0001-015) in the open ports of the machine’s hydraulic valve.

NOTE:

Use grease or petroleum jelly to hold the O-rings in place during the AutoBoom valve installation, 

taking care to avoid contamination of the inside of the open ports.

FIGURE 2. O-Rings Installed on the Machine’s Hydraulic Valve

Before

After

Surface 

to be 

Stripped

Allen 

Plugs

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments