Raven AutoBoom UltraGlide XT Installation Manual Download Page 27

Page: 27 / 78

CHAPTER

Manual No. 016-0171-122 Rev. E

CHAPTER 3

HYDRAULIC SYSTEM

INSTALLATION

WARNING

The machine must remain stationary and

switched off, with the booms folded and in the

transport position, during installation or

maintenance.

Bleed pressure from the hydraulic system by

operating the boom tilt functions while the key is

on, but the machine’s engine is off.

CAUTION

When installing AutoBoom hydraulics or

performing diagnostics, maintenance, or routine

service, ensure precautions are taken to prevent

any foreign material from being introduced into

the machine’s hydraulic system.

Objects that are able to bypass the machine’s

hydraulic filtration system will reduce

performance and possible damage the

AutoBoom hydraulic valve.

NOTICE

The appearance of the AutoBoom hydraulic valve

may vary slightly from the images contained in

this manual. However, the fittings, hose

connections, and cable connections remain the

same.

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 27 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: