manualshive.com logo in svg

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 46 / 78

Share
Download
Raven AutoBoom UltraGlide XT Installation Manual Download Page 46

C

HAPTER

 4

42

Viper Pro Installation & Operation Manual

INSTALL THE ROTARY SENSOR

FIGURE 8. Rotary Sensor Installed on Mounting Bracket

1. Determine the correct rotary sensor bracket for your machine.

•

2009 RoGator - P/N 107-0172-177

•

2010-2011 RoGator - P/N 107-0172-177 or P/N 107-0172-268

•

2012 and Newer RoGator - P/N 107-0172-268

2. Install the non-contact rotary sensor (P/N 063-0181-018) on the rotary sensor bracket using two #8-32 x 

1/2” screws (P/N 311-0001-013) and two #8-32 hex nuts (P/N 312-1001-020).

FIGURE 9. Pivot Bearing Bolt to be Removed

3. Remove the horizontal bolt at the rear of the pivot bearing.

NOTE:

The existing washers will be used later in the installation procedure. The original bolt and hex nut will 

not be reused in the UltraGlide XT installation.

Sensor Installed on Bracket P/N 107-0172-268

Sensor Installed on Bracket P/N 107-0172-177

Summary of Contents for AutoBoom UltraGlide XT















































































Reviews:

No comments