Raven AutoBoom UltraGlide XT Installation Manual Download Page 49

Page: 49 / 78

CHAPTER

Manual No. 016-0171-122 Rev. E

CHAPTER 5

WIRING INSTALLATION

WIRING CONNECTIONS

For wiring connections made outside the cab, apply dielectric silicone grease (P/N 222-0000-006) generously on

both the male and female ends of the connectors. Application of the grease will prevent corrosion to the pins and

wires.

MODEL YEAR 2012 & NEWER RG SERIES NODE AND HARNESS

INSTALLATION

INSTALL THE NODE HARNESS

1. Locate the node mounting box at the front-right corner of the liquid tank

and remove the cover.

2. Remove the existing AutoBoom node and disconnect the cable connectors from it, if applicable.

FIGURE 1. Bulkhead Connector to be Removed

3. Disconnect the SYS BLKHD 5 connector from the back of the node box.

CAUTION

Always connect the power cable as the last step

in the wiring process and verify that the power

leads are connected with the correct polarity.

Reversing power leads can cause severe damage

to the equipment.

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 49 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: