Raven AutoBoom UltraGlide XT Installation Manual Download Page 7

Page: 7 / 78

CHAPTER

Manual No. 016-0171-122 Rev. E

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the Raven AutoBoom system! This system is designed to provide automated

boom height adjustment for agricultural equipment.This manual applies to the machines listed below.

MAKE: AGCO RoGator

YEAR: 2009

MODEL: 884, SS884, 1084, 1084C, SS1084, SSC1084, and 1286C

YEAR: 2010-2011

MODEL: 984, 984H, 994, 994H, 1184, 1184H, 1194, 1194H, 1386, and 1396

YEAR: 2012 & Newer

MODEL: RG900, RG900B, RG1100, RG1100B, RG1300, and RG1300B

FIGURE 1. AGCO RoGator RG1100

PREPARING FOR INSTALLATION

Before installing AutoBoom:

• Park the machine on dry, clean, and level land.
• Leave the machine off during the installation process.
• Read the instructions in this manual as you complete the installation process.

Summary of Contents for AutoBoom UltraGlide XT














































































Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews:

Raven AutoBoom UltraGlide XT, Installation Manual, Page: 7 / 78

Search results

Summary of Contents for AutoBoom UltraGlide XT

Reviews: