manualshive.com logo in svg

Racepak 250-DS-IQ3SL, Installation Manual, Page: 4 / 63

Share
Download
Racepak 250-DS-IQ3SL Installation Manual Download Page 4

IQ3 Street Logger Dash Installation Manual  

 

 

4

 

DatalinkII Software Installation ................................................................. 34

 

Configuration Files ..................................................................................... 35

 

Stand Alone or with V-Net Sensors ................................................................................................ 35

 

 

Programming the Display Using the DataLink Software ........................... 36

 

 

Com Port Settings ........................................................................................................................... 36

 

Reading/Syncing of the Configuration File ..................................................................................... 37

 

EFI Interface Programming ............................................................................................................. 38

 

Programming the Display Pages ..................................................................................................... 40

 

Programming the Warnings ........................................................................................................... 42

 

Example Warning Setup ................................................................................................................. 43 
Shift Lights ...................................................................................................................................... 43 
Gear Ratio Calculation .................................................................................................................... 43 

 

DataLink II Logging and Downloading ....................................................... 45

 

 

Data Download Path ....................................................................................................................... 45 
Setting the Correct Time and Date inside Your IQ3 Street Logger Dash ........................................ 46

 

Clearing Data Files from the Memory Card .................................................................................... 47

 

Initiating a Recording with the IQ3 Street Logger Dash ................................................................. 48

 

Recording Data ............................................................................................................................... 49 
Configuring the Record Parameters ............................................................................................... 50 
Uploading Recorded Data to your PC from the IQ3 Street Logger Dash ........................................ 53 
Viewing Real Time Data on your PC ............................................................................................... 56 
Setting up the Logger Real Time Telemetry Parameters ................................................................ 57 
Starting a Telemetry Session .......................................................................................................... 58 
DataLink II Help Files ...................................................................................................................... 59

 

 

Dash Info Tab ............................................................................................ 60

 

 

Maximum Numbers of Recording VNET Channels allowed ............................................................ 60

 

Record Enable Channel ................................................................................................................... 60

 

ECU Type......................................................................................................................................... 60

 

Turn Signal Input Off Delay ............................................................................................................. 60 
Odometer Input Channel ................................................................................................................ 60 
Dim Back Light Channel .................................................................................................................. 60 
Dash Model .................................................................................................................................... 60 
Serial # ............................................................................................................................................ 60 
Firmware Version ........................................................................................................................... 60 

 

Troubleshooting and FAQ ....................................................................... 62

 

 

DataLink will not communicate with the IQ3 when using the USB programming cable ................ 62

 

V-Net Sensor Channels “lock up” from time to time ...................................................................... 62

 

 

Conclusion .............................................................................................. 63

 

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments