manualshive.com logo in svg

Racepak 250-DS-IQ3SL, Installation Manual, Page: 59 / 63

Share
Download
Racepak 250-DS-IQ3SL Installation Manual Download Page 59

IQ3 Street Logger Dash Installation Manual  

 

 

 

  

59

 

To stop the data acquisition, left click on the Stop Data Acquisition icon located at the bottom of 

the tool bar.  The real time data acquisition session will be suspended.  
   

If you wish to continue the real time data acquisition, simply click on the Start Data Acquisition 

icon.  The telemetry session will restart at the same point it was suspended.  If you wish to restart 
the session from the beginning, select Erase from the Telemetry main menu.  All previously 
recorded data will be erased from the file.  

  

 

If you wish to save the data, stop the data acquisition, and click the Save icon located in the tool 

bar, or select Save located in the File main menu.  
   

DataLink II Help Files  

  

The DataLink II software includes a complete selection of help files, which can be accessed as 

shown below:  
  

Main Menu or any open Dialog Box: To get help for any of the menu items simply highlight the 

menu item by placing the mouse cursor over the menu item.  Next press the F1 key to display the 
help.   
  

Icon Tool Bar:  Select the ? button located at the bottom of the icon toolbar.  The mouse 

cursor will change to a? Position the mouse cursor over toolbar icon for which help is desired and 
click the left mouse cursor.  Help will be displayed   
  

DataLink Program Screens:  Select the ?  button located at the bottom of the icon toolbar.  

The mouse cursor will change to a?  Position the mouse cursor over the section of the DataLink II 
screen for which help is desired and click the mouse button.  Help will be displayed.  
  

Runlog Pages:  To get help on a run log page look for the blue icon with a question mark.  

Simply click on the button to display the help for the run log page.  
  

Help from Main Menu: Click on the Help main menu selection and select the Help Topics menu 

selection.  The Help Topics: DataLink II Applications Help will be displayed.  Follow the instructions 
included with the help box to navigate thru the online help  
  

 

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments