manualshive.com logo in svg

Racepak 250-DS-IQ3SL, Installation Manual, Page: 22 / 63

Share
Download
Racepak 250-DS-IQ3SL Installation Manual Download Page 22

IQ3 Street Logger Dash Installation Manual  

 

 

22

 

Button Functions in Normal Display

 (Stationary) mode 

 

While the IQ3 Street Logger Dash is in normal display mode, the programming buttons will perform the 

following functions:  

  

Button  

Short Press (1 flash)  

Medium Press (2 flashes)   Long Press (3 flashes)  

Button 1 

 

Advance to Next Display Page 

 

Enter Setup Mode 1 

 

Displays the current time in 
upper right display position 

 

Button 2 

 

Clear/Acknowledge any Active 

 

Warnings 

 

Enter Setup Mode 2 

 

Does nothing 

 

 

 

Button Functions in Setup Mode  

While the IQ3 Street Logger Dash is in setup mode, the programming buttons will perform the following 

functions:  

Button  

Short Press (1 flash)  

Medium Press (2 flashes)   Long Press (3 flashes)  

Button 1 

 

Advances to Next Available 

 

Parameter 

 

Accepts change and advances 
to next available parameter. 

 

Saves Changes and Exits 

 

Button 2 

 

Changes Parameter Value  (see 
below  programming  chart  for 
each parameter) 

 

Changes  Parameter  Value  (see 
below  programming  chart  for 
each parameter) 

 

Changes  Parameter  Value 
(see  below  programming 
chart for each parameter) 

 

  

Programming in Setup Mode  

The programming functions are arranged in a pre-defined order. This allows the user to enter the 

programming mode, and then toggle through to the desired feature by using the left or right button, 
depending on the mode.

 

 

Setup Mode is used to program the unit without the need to connect to a PC. It is utilized to program items 

such as screen brightness, LED brightness, reset to defaults, etc.  

 

 

Entering Setup 1  

1.

 

Press and hold the Button 1 for TWO shift light blinks – MEDIUM press  

2.

 

The Dash will display SETUP 1?   

3.

 

Confirm you wish to enter the setup mode by pressing the Button 1 for ONE shift light blink  
– SHORT press  
To cancel entering Setup Mode 1, press the Button 2 for a SHORT press  

The following are in the order in which the individual programming features will appear.   
  

Setting as  
Displayed on  
Dash  

Program   
Setting Description  

Programming  
Command  
 

 

Accept and  
Advance  

  

 

Accept and  
Exit   

  

 

 

RESET TRIP ODO 

 

Resets odometer setting to zero  

 

N = No    

 

Y = Yes 

 

Short Press Button 2 
to toggle between 
Y/N 

 

Short Press 

 

Button 1 

 

Long Press 

 

Button 1 

 

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments