manualshive.com logo in svg

Racepak 250-DS-IQ3SL, Installation Manual, Page: 34 / 63

Share
Download
Racepak 250-DS-IQ3SL Installation Manual Download Page 34

IQ3 Street Logger Dash Installation Manual  

 

 

34

 

DatalinkII Software Installation  

The DatalinkII software is utilized to program the IQ3 Street Logger Dash unit. If a previous version 

of DatalinkII exists on the programming PC, update to the latest DatalinkII software (version 4.6.0 
or higher), included with the IQ3 Street Logger Dash package.    

 

 

During the program installation (step 7), select the unit to be utilized. Be sure to select “IQ3 
Configuration for Street ”, as this will install the necessary files needed for the IQ3 Street 
Logger Dash unit.

  

To install the software

 

 

 

 

 

1.

 

Close all/any programs before beginning the DatalinkII installation  

2.

 

Insert Racepak USB Memory Flash Drive a USB port of the Laptop/PC  

3.

 

After a few seconds, the installation program should automatically start  

4.

 

“Welcome to the Install Wizard for DatalinkII”.  Click Next  

5.

 

“License Agreement”.  After reading, Click Yes  

6.

 

“Choose Destination Location” Default C:\Program Files\DatalinkII,  Click Next  

7.

 

“Data Logger Installation and Support”, Select the check box for IQ3 Configuration 
for Street , Click Next  

8.

 

“Select Program Folder”, Default is DatalinkII, Click Next  

9.

 

Install will start as noted by progress bar  

10.

 

Installing for the first time, a “Welcome to the Install Wizard for PL-2303 USB-to-

Serial” window will open, Click Next  

11.

 

“License Agreement”,  after reading, Click YES  

12.

 

Installation PL-2303 Wizard Complete, Click Finish  

13.

 

Installation Wizard Complete, Click Finish  

14.

 

DatalinkII will now open  

15.

 

Software Installation Complete  
   

Upon completion of installation, a new shortcut icon (shown right) will be added to 

the PC desktop with a title “DatalinkII Program”. Double click on the icon to start the 
DatalinkII software.  

 

 

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments