Racepak 250-DS-IQ3SL Installation Manual Download Page 27 | Manualshive

Page: 27 / 63

Racepak 250-DS-IQ3SL Installation Manual Download Page 27

IQ3 Street Logger Dash Installation Manual

27

Oil Pressure, Water and Transmission Temperature Sensor Installation:

The water and oil sensors provided use 1/8” NPT thread. An adaptor may be required to

accommodate larger thread sizes. Make sure to use thread sealer when installing the sensors to
prevent water and oil leaks. DO NOT use excessive amount of thread sealer on factory supplied
temperature sensor since the sensor must ground via threads for proper operation.

Ensure that temperature sensors are threaded into item that is grounded to the chassis.

Oil Pressure Sensor Settings

The dash is pre-configured at the factory to use a supplied two-wire 100 psi sender for oil

pressure on Pin#13, Tan wire. The option to use other sensors instead of the supplied two-wire
pressure sensor is available as well as using this input for other parameters beside oil pressure.
When using powered sensors, extra terminals are available on rear connector of dash for 5 volt
power and ground.

#

Wires

ONSCREEN

NAME

R

ANGE

N

OTES

&

S

CALING

2

100 PSI

0 - 100 psi

Racepak #810-PT-

0100SD Ω style with 499 Ohm pull-up

3

150 PSI

0 - 150 psi

Racepak #810-PT-0150GVT 5v powered, .5v=0 4.5v=150

3

300 PSI

0 - 300 psi

Racepak #810-PT-0300GVT 5v powered, .5v=0 4.5v=300

3

500 PSI

0 - 500 psi

Racepak #810-PT-0500GVT 5v powered, .5v=0 4.5v=500

3

1500 PSI

0 - 1500 psi

Racepak #810-PT-1500HP 5v powered, .5v=0 4.5v=1500

3

3000 PSI

0 - 3000 psi

Racepak #810-PT-3000HP 5v powered, .5v=0 4.5v=3000

3

Vacuum - KPA

0 - 30 Vac kPa

Racepak #810-PT-VB 5v powered, 1.8v=0 .5v=105

3

15 PSI - KPA

0 - 103 kPa

Racepak #810-PT-0015GVT 5v powered, .5v=0 4.5v=103.42

3

75 PSI - KPA

0 - 517 kPa

Racepak #810-PT-0075GVT 5v powered, .5v=0 4.5v=517.1

2

100 PSI - KPA

0 - 690 kPa

Racepak #810-PT-

0100SD Ω style with 499 Ohm pull-up

3

150 PSI - KPA

0 - 1034 kPa

Racepak #810-PT-0150GVT 5v powered, .5v=0 4.5v=1034.2

3

300 PSI - KPA

0 - 2068 kPa

Racepak #810-PT-0300GVT 5v powered, .5v=0 4.5v=2068.4

3

500 PSI - KPA

0 - 3447 kPa

Racepak #810-PT-0500GVT 5v powered, .5v=0 4.5v=3447

3

1500 PSI - KPA

0 - 10342 kPa

Racepak #810-PT-1500HP 5v powered, .5v=0 4.5v=10342

3

3000 PSI - KPA

0 - 20684 kPa

Racepak #810-PT-3000HP 5v powered, .5v=0 4.5v=20684

User Cal

Custom user scale

Disabled

Disabled, input is not used and will not stream/record data

0-5 volts

0-5 volt input, must use software to program, Raw Data A, Raw
Data B, Min, Max Result Values

3

VACUUM

0-30 inHg

Racepak #810-PT-VB 5v powered, 1.8v=0 .5v=29

3

15 PSI

0

– 15 psi

Racepak #810-PT-0015GVT 5v powered, .5v=0 4.5v=15

3

75 PSI

0

– 75 psi

Racepak #810-PT-0075GVT 5v powered, .5v=0 4.5v=75

«
...
25
26
27
28
29
...
»

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments