Racepak 250-DS-IQ3SL Installation Manual Download Page 3

Page: 3 / 63

IQ3 Street Logger Dash Installation Manual

Disclaimer .................................................................................................... 2

Warranty ...................................................................................................... 2

Manual Summary ............................................................................................................................. 5

Manual Quick View ........................................................................................................................... 5

Items Included with the IQ3 Street Logger Dash Display Kit ............................................................ 5

IQ3 Street Logger Dash Features ...................................................................................................... 6

General Feature Overview................................................................................................................ 6

IQ3 Street Logger Dash Displayed Features ..................................................................................... 7

Technical Specifications .................................................................................................................... 8

IQ3 Street Logger Dash Functions .................................................................................................... 9

PC Minimum Requirements ............................................................................................................. 9

DataLink Programming Software ...................................................................................................... 9

IQ3 Street Logger Dash Configuration File (software) ...................................................................... 9
Data Recording Activation ................................................................................................................ 9

Terminology ...................................................................................................................................... 9

Hardware Features .................................................................................... 10

Mounting Dimensions .................................................................................................................. 122

Installation ...................................................................................................................................... 13

General Mounting Requirements ................................................................................................... 13

Heat ................................................................................................................................................ 13

IQ3 Street Logger Dash Wiring Pinout ....................................................... 14

External Programming Button and Fan Output Wiring Diagram .................................................... 17

External V-Net Sensor Connection (optional add ons) ................................................................... 18

Factory Default Display Settings ................................................................ 19

External Programming Buttons .................................................................. 21

Button Programming Modes .......................................................................................................... 21

General Button Operation (Display and Setup) .............................................................................. 21

Button Functions in Normal Display (Stationary) mode ................................................................. 22

Button Functions in Setup Mode .................................................................................................... 22

Programming in Setup Mode ......................................................................................................... 22

Oil Pressure, Water and Transmission Temperature Sensor Installation: ...................................... 27

Oil Pressure Sensor Settings ........................................................................................................... 27

Water Temperature Sensor Settings .............................................................................................. 28

Oil Temperature Sensor Settings .................................................................................................... 28

Fuel Level ........................................................................................................................................ 29

Speedometer Sensor Interface ....................................................................................................... 30

Display Clock/Time ......................................................................................................................... 30

OBDII and EFI Interface:

............................................................................................................... 32

Summary of Contents for 250-DS-IQ3SL
































































Search results

Summary of Contents for 250-DS-IQ3SL

Reviews:

Racepak 250-DS-IQ3SL, Installation Manual, Page: 3 / 63

Search results

Summary of Contents for 250-DS-IQ3SL

Reviews: