manualshive.com logo in svg

Racepak 250-DS-IQ3SL, Installation Manual, Page: 5 / 63

Share
Download
Racepak 250-DS-IQ3SL Installation Manual Download Page 5

IQ3 Street Logger Dash Installation Manual  

 

 

 

  

5

 

Manual Summary  

This manual makes the assumption that you have installed the most current version of the DataLink 

PC software and IQ3 firmware.  IQ3 Street Logger Dash firmware and DataLink updates can be found 
at 

http://www.racepak.com/downloads

.  As of this writing, the most current DataLink version is 

4.8.0 and the most current IQ3 Street Logger Dash firmware version is 3.7.  
  

Manual Quick View  

The following provides a quick view of the manual layout:  

  

1.

 

 IQ3 Street Logger Dash Features  

a.

 

Dash  

b.

 

Available channels for display  

c.

 

External optional sensors  

d.

 

Technical specifications  

2.

 

Installation  

a.

 

Dash  

b.

 

Software  

3.

 

Programming The Display  

4.

 

Adding Sensors 

5.

 

Software Usage 

  

Items Included with the IQ3 Street Logger Dash Display Kit  

  

Qty.   Part Number  

Description  

1  

250-DS-IQ3SL 

IQ3 Street Logger Dash Display Kit (incls. all below items)  

1  

280-CA-IQ3S 

Harness/Street Dash Interface  

1  

280-CA-VM-TCAPM  

V-Net Male Terminator Cap  

1  

890-CA-USBABM-6  

USB Programming/Communication Cable  

1  

890-DR-USB-2GB  

DataLink Software Memory Stick  

2  

800-SW-PSHBTN  

Momentary Style Push Buttons, spade terminal  

1  

890-SD-M4GB  

4GB Micro SD Memory Card and adapter 

1  

890-SD-RDR-5 

USB Memory Card adapter 

1  

N/A  

Installation Manual  

 

 

 

Summary of Contents for 250-DS-IQ3SL
































































Reviews:

No comments