Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 68 | Manualshive

Page: 68 / 147

background image

• Improperly installed or adjusted components can result in a system failure. If

you do not have the time, tools and expertise necessary to complete a
procedure properly, please see your dealer or another qualified person for
service.

• Review the safety-related maintenance information on page 16.
• Before beginning any maintenance procedure, read the instructions for the

entire procedure.

•  Always position the vehicle on a firm level surface before performing service.
•  Wear eye and face protection when using pressurized air.
•  Never start the engine or let it run in an enclosed area. Engine exhaust fumes

are poisonous and can cause loss of consciousness or death in a short time.

• During some procedures you may use potentially hazardous products such as

oil, coolant, or brake fluid. Always follow the instructions and warnings on the
product packaging.

ELEVATING THE VEHICLE FOR SERVICE

WARNING

Serious injury or death can occur if the vehicle moves or falls while elevated.

When elevating is necessary, make sure the vehicle is properly elevated and

stable before performing service.

Some procedures require elevating the vehicle. DO NOT attempt to elevate your
vehicle without proper equipment. If you’re not familiar with using floor jacks or
lift mechanisms, see your dealer for service.

To elevate the SLINGSHOT vehicle, use automotive-quality floor jacks. Use the
floor jacks on a firm, flat surface.

Make sure the floor jacks are positioned under the frame rails in the front where
the lower control arm mounts to the frame, or in the rear where the frame rails
meet.

For fluid changes, always make sure the elevated vehicle is level.

Bottom View of Lift Points

Side View of Lift Points

66

Downloaded from

«
...
66
67
68
69
70
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Eclipse Pages: 6

Brand: iArmor Pages: 6

Brand: Warrior Products Pages: 4

Brand: Metra Electronics Pages: 2

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: Subaru Pages: 34

Brand: kincrome Pages: 6

Brand: Thule Pages: 12

Brand: BMW Pages: 38

Brand: Road Ranger Pages: 22

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: Thule Pages: 12

Brand: Lexus Pages: 34

Brand: Toyota Pages: 32

Brand: Black Horse Off Road Pages: 7

Brand: Kia Pages: 58

Brand: AutoLoc Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands