Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 37 | Manualshive

Page: 37 / 147

background image

• The anti-lock brake system will not prevent wheel lockup, loss of traction or

loss of control

under all conditions.

Always adhere to all safe operating

practices as recommended.

• It is not unusual to leave tire marks on the road surface during a hard braking

event.

• The anti-lock brake system does not compensate for or reduce the risks

associated with:
–  excessive speed
–  reduced traction on rough, uneven or loose surfaces
–  poor judgment
–  improper operation
–  hydroplaning

PARK BRAKE LEVER

The park brake lever is located between the seats. To help prevent the vehicle
from rolling, engage the park brake when the vehicle is parked. When the park
brake is engaged and the park brake indicator is illuminated, the vehicle will not
move. Always apply the brakes before engaging or releasing the park brake.

1. To engage the park brake, apply the brakes. Pull the park brake lever upward

as far as possible.

2. To release the park brake, apply the brakes. Press the park brake release

q

inward and move the lever downward as far as possible.

WARNING

Always make sure parking brake is fully released before attempting to move

the vehicle. Failure to do so can cause damage to the rear brakes.

35

FEATURES AND CONTROLS

Downloaded from

«
...
35
36
37
38
39
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Laser Pages: 8

Brand: Whispbar Pages: 16

Brand: Horn Tools Pages: 6

Brand: Brodit Pages: 2

Brand: Thule Pages: 8

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Hummer Pages: 502

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

Brand: Oldsmobile Pages: 276

Brand: Volkswagen Pages: 32

Brand: STO N SHO Pages: 7

Brand: Alfa Romeo Pages: 268

Brand: Ford Pages: 46

DELTA HF integrale

Brand: Lancia Pages: 101

Brand: Racepak Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands