Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 134 | Manualshive

Page: 134 / 147

background image

NOISE EMISSION WARRANTY

POLARIS warrants that this exhaust system, at the time of sale, meets all
applicable U.S. EPA Federal noise

standards. This warranty extends to the first person who buys this exhaust
system for purposes other than resale,

and to all subsequent buyers.

Warranty claims should be directed to:

• An authorized POLARIS dealer, or
• POLARIS Industries Inc., 2100 Highway 55, Medina, MN 55340

FEDERAL EMISSIONS CONTROL SYSTEM
WARRANTY

This Federal Emissions Control System Warranty Statement applies to your
SLINGSHOT vehicle, which is certified to meet U.S. EPA emission standards.
This same emissions warranty coverage applies to SLINGSHOT vehicles sold in
Canada.

YOUR WARRANTY RIGHTS AND OBLIGATIONS

In the United States, new motor vehicles must be designed, built and equipped
to meet applicable emission standards set forth in the Clean Air Act and in U.S.
EPA regulations. POLARIS Industries Inc. (hereinafter POLARIS) must warrant
the emission control system on your vehicle for the periods of time listed below
provided there has been no abuse, neglect or improper maintenance of your
vehicle.

Your emission control system may include parts such as the fuel-injection
system, ignition system, catalytic converter and engine computer. Also included
may be hoses, belts, connectors and other emission-related assemblies. Where
a warrantable condition exists, POLARIS will repair your vehicle at no cost to
you, including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The emissions warranty coverage for this vehicle is for a period of use of five (5)
years or 30,000 kilometers (18,641 miles), whichever first occurs first. If an
emission-related part on your vehicle is defective, the part will be repaired or
replaced by POLARIS. This is your emission control system DEFECTS
WARRANTY.

132

Downloaded from

«
...
132
133
134
135
136
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Falcon Pages: 8

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: Ford Pages: 12

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: BrandMotion Pages: 2

Brand: SCC Pages: 4

Brand: Magneti Marelli Pages: 2

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Subaru Pages: 44

Brand: Westfalia Pages: 10

Brand: Rugged Ridge Pages: 5

Brand: Great day Pages: 5

Brand: Saab Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands