Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 147

background image

HOOD

Open the hood to access the engine compartment. The hood release lever is
located between the headlights.

1. Push the hood release lever

q

downward to disengage the four hood

latches.

CAUTION

Engine components may be hot after use. Always use only the hood handle

when opening the hood. Do not grasp the hood edges.

2. The metal hood handle

w

is a plate located above the release lever and on

the underside of the hood plastic. Firmly grasp the hood handle and pull the
hood upward and forward, rotating the hood to a vertical position at the front
of the vehicle.

3. To close the hood, grasp the hood handle. Pull the handle upward and

toward the vehicle until the hood is fully seated. Apply firm downward
pressure on the hood at all four latch points to ensure the hood is securely
latched at all four points.

38

FEATURES AND CONTROLS

Downloaded from

«
...
38
39
40
41
42
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: iDataLink Pages: 9

Brand: Hama Pages: 2

Brand: JANE Pages: 21

V2 SUPERCHARGER

Brand: Tesla Pages: 9

3-series convertible

Brand: BMW Pages: 98

Brand: BESAFE Pages: 4

Brand: Thule Pages: 12

Brand: Ford Pages: 368

Brand: Webasto Pages: 18

Brand: Mobility Networks Pages: 52

Brand: Guidosimplex Pages: 8

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: PUTCO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands