Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 62

Page: 62 / 147

STOPPING THE ENGINE

Bring the vehicle to a complete stop before stopping the engine.

NOTE

Stopping the engine with the transmission in gear while the vehicle is moving

could cause loss of rear wheel traction or engine and transmission damage,

which could cause loss of control and serious injury or death. Always stop the

engine after the vehicle is fully stopped and the transmission is in neutral (or

clutch is disengaged). If the engine stops unexpectedly while the vehicle is

moving, guide the vehicle to a safe location off the road and away from traffic.

1. Brake to a complete stop. When nearly stopped, disengage the clutch.

NOTE

As the vehicle slows, disengage the clutch, or downshift each time vehicle

speed reaches a downshift point.

2. When fully stopped, move the ignition switch to the OFF position.

3. Remove the ignition key.

4. Engage the park brake.

OPERATION

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands