Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 147

background image

LAMP

INDICATES

CONDITION

system is inoperative. Your dealer can inspect the vehicle
and perform service if the lamp illuminates after starting the
engine.

Park Brake
Engaged

This lamp illuminates when the park brake is engaged. If it
illuminates when the park brake is NOT engaged, your
dealer can inspect the vehicle and perform service

Low Oil
Pressure

This lamp illuminates if engine oil pressure drops below
safe operating pressure. If this lamp illuminates while the
engine is running, turn the engine off as soon as safely
possible and check the oil level.

If the oil level is correct and

the lamp remains on after the engine is restarted, turn the
engine off immediately.

Chassis
Warning

The chassis warning lamp is meant for other POLARIS
vehicles, and will not illuminate on a SLINGSHOT.

MULTI-FUNCTION DISPLAY

WARNING

Driving while distracted can result in loss of vehicle control, crash and serious

injury or death. Use extreme caution when using any device that may take your

focus off the road.

Use the mode button to toggle through the modes of the multi-function display.
See page 23. Press and hold the mode button to reset the trip odometers and
average fuel economy.

MODES AVAILABLE

Fuel Level Gauge

Fuel Range

Trip Odometer 1

Average Fuel Economy

Trip Odometer 2

Clock

Ambient Air Temperature

27

FEATURES AND CONTROLS

Downloaded from

«
...
27
28
29
30
31
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: KC HiLiTES Pages: 4

Brand: EAL Pages: 4

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

Brand: Warrior Products Pages: 3

Brand: Thule Pages: 8

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

2011 3500 Chassis Cab

Brand: RAM Pages: 92

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Volvo Pages: 24

Brand: Chevrolet Pages: 428

Brand: Demco Pages: 4

Brand: Pontiac Pages: 20

Brand: true-i Pages: 11

Brand: Westin Pages: 3

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brand: SkyRack Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands