Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 88

Page: 88 / 147

CLUTCH FLUID LEVEL

1. Position the vehicle on a level surface.

2. Place the transmission in gear.

3. Open the hood.

4. Wipe the fluid container and the area around the reservoir cover with a clean

cloth.

WARNING

Using the wrong fluid or allowing air or contaminants into the fluid system can

damage the system seals or result in a malfunction that could lead to serious

injury or death. Do not operate the clutch while the reservoir cover is removed.

Fluid could overflow from the reservoir and cause air to enter the fluid system.

5. View the fluid level in the reservoir. If the fluid level is below the MIN line on

the reservoir, remove the cap and add the recommended fluid to the MAX
line. Do not overfill.

6. Reinstall the reservoir cap.

7. Depress the clutch pedal forcefully for a few seconds. Check for fluid leakage

around the clutch reservoir fittings.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands