Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 85 | Manualshive

Page: 85 / 147

background image

9. Tighten the clamp on the air filter.

TORQUE

Clamp: 2.6-3.25 ft-lbs (3.5-4.4 Nm)

10. Close the hood.

DRIVE BELT CONDITION

Adjust drive belt tension after the first 2,500 miles (4,000 km) of operation.
Replace the drive belt

q

and both sprockets as a set if the drive belt has over

30,000 miles (48,000 km) of service at the time of damage or failure.

When inspecting the drive belt for signs of wear, refer to the Drive Belt Wear
Analysis table on the next page to determine whether the belt needs to be
replaced. See the

SLINGSHOT Service Manual

or an authorized dealer for more

information.

DO NOT attempt to check belt tension if the belt has been exposed to rain or
washing within a 24 hour period or if the belt is hot from being in use. Allow the
belt to cool down to ambient temperature before measuring belt tension.

83

Downloaded from

«
...
83
84
85
86
87
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Hama Pages: 2

Brand: Victory 4x4 Pages: 13

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Fab Fours Pages: 19

Brand: CTEK Pages: 84

TX-STAMP-4-FC04

Brand: Over Armour Offroad Pages: 9

Brand: A-Tach Mounts Pages: 2

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Volvo Pages: 10

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands