Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 6 | Manualshive

Page: 6 / 147

background image

The following signal words and symbols appear throughout this manual and on
your vehicle. Your safety is involved when these words and symbols are used.
Become familiar with their meanings before reading the manual.

DANGER

DANGER indicates a hazardous situation which, if not avoided, WILL result in

death or serious injury.

WARNING

SAFETY ALERT WARNING indicates a hazardous situation which, if not

avoided, COULD result in serious injury.

CAUTION

SAFETY ALERT CAUTION indicates a hazardous situation which, if not

avoided, COULD result in minor to moderate injury.

CAUTION

CAUTION indicates special precautions that must be taken to avoid vehicle

damage or property damage.

IMPORTANT

IMPORTANT provides key reminders during disassembly, assembly, and

inspection of components.

NOTICE

NOTICE provides key information by clarifying instructions.

The Prohibition Safety Sign indicates an action NOT to take in order
to avoid a hazard.

The Mandatory Action Sign indicates an action that NEEDS to be
taken to avoid a hazard.

4

SAFETY SYMBOLS AND SIGNAL WORDS

Downloaded from

«
...
4
5
6
7
8
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: E&G Classics Pages: 2

Brand: Daesung Pages: 9

Brand: Pontiac Pages: 318

Brand: Unex Pages: 30

Brand: Oldsmobile Pages: 354

Brand: AIS Pages: 2

Brand: Rugged Ridge Pages: 2

Brand: AL-KO Pages: 40

Brand: J. Strong Pages: 2

Brand: Magneti Marelli Pages: 2

Brand: Adaptiv Mini Pages: 4

Brand: NavLinkz Pages: 24

TV-Free CI-TF-C25

Brand: Car-Interface Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands