Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 95

Page: 95 / 147

TIRE PRESSURE

For an accurate reading, check tire pressure when tires are cold. Driving warms
the tires and increases tire air pressure.

1. Remove the valve stem cap

2. Adjust tire pressure to the recommended specification. Refer to safety labels

on the vehicle or to the specifications section beginning on page 121.

WARNING

Do not exceed the maximum recommended inflation pressure to seat the

bead. Tire or rim failure may result.

WHEEL INSPECTION

Inspect all wheels for cracks or other damage. Replace damaged wheels
promptly. Do not operate the vehicle if wheels are damaged or cracked.

WHEEL REMOVAL

1. Position the vehicle on a firm, level surface.

2. Place the transmission in gear.

3. Engage the park brake.

4. Position an appropriate floor jack under the frame at the side or rear of the

vehicle, near the wheel to be removed.

5. If removing the rear wheel, place wheel chocks at the front of both front

wheels to prevent rolling.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands