Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 147

background image

HAZARD SWITCH/EMERGENCY FLASHERS

All turn signals flash when the emergency flashers are
activated. Press the top of the hazard switch to turn
the flashers on. Press the bottom of the switch to turn
the flashers off. The ignition switch does not have to
be on to activate the flashers.

MASTER LIGHTING SWITCH (CANADA)

The master lighting switch must be in the ON position to allow operation of the
high beam headlights.

ONE-TOUCH STARTER SWITCH

Use the one-touch starter switch to start the engine. Read the engine starting
procedures before starting the engine. See the Starting the Engine section for
details.

MODE BUTTON

The mode button is located on the dashboard near the instrument cluster.

Use the mode button to toggle through the modes of the multi-function display.
See page 27. Use the mode button to set the display units to either standard or
metric units of measurement. See page 28.

ELECTRONIC STABILITY PROGRAM (ESP) SWITCH

The ESP is active by default. This feature helps reduce the risk of accident by
providing traction control and stability control. If ESP senses a loss of stability
due to loss of traction (skidding) the ESP intervenes by automatically applying
brakes to one or more wheels and reducing power to the rear wheel.

WARNING

No stability control, traction control or anti-lock braking system can fully protect

you from every situation. Always be mindful of road conditions. Always drive

safely and within the limits of the driver, vehicle and road conditions.

WARNING

Stability control, traction control and anti-lock braking systems rely on grip

between the tires and the road to function properly. In a hydroplane situation,

tires lose contact with the road and the effectiveness of these features may be

diminished.

23

FEATURES AND CONTROLS

Downloaded from

«
...
23
24
25
26
27
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: LAMBORGHINI Pages: 48

Brand: Whispbar Pages: 16

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

Brand: Phonocar Pages: 6

Intercooler Kit Type 31

Brand: GReddy Pages: 9

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Whispbar Pages: 17

Brand: Sagem Pages: 10

Brand: Yakima Pages: 11

2011 Camry SE V6

Brand: Toyota Pages: 33

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Brand: QA1 Pages: 3

Brand: Ford Pages: 256

Brand: Ranger design Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands