Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 147

background image

HEADLIGHT HIGH/LOW BEAM SWITCH

The headlights are always on when the ignition switch is in the ON position. To
switch the headlights between low beam and high beam, tap the turn signal
lever forward, toward the steering wheel. The master lighting switch (Canada)
must be in the ON position to allow operation of the high beam headlights. See
page 23.

TURN SIGNAL LEVER

Before turning, activate a turn signal to alert others of your intentions. Check turn
signal lamps before each ride.

NOTE

The key must be in the ON position to activate the turn signals.

1. Move the turn signal lever downward to signal a left turn. The left turn signal

lamps at the front and rear of the vehicle will flash. The indicator arrows on
the console will flash when a turn signal or hazard signal is activated.

2. Move the lever upward to signal a right turn. The right signal lamps and

indicator will flash.

3. The turn signal automatically cancels and the lever returns to the center

position when the turn is completed.

CRUISE CONTROL SWITCHES

The cruise control switch

q

and set button

w

are located on the turn signal lever.

Before using the cruise control, read the safety and operation procedures. See
page 61.

22

FEATURES AND CONTROLS

Downloaded from

«
...
22
23
24
25
26
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: ULTIMATE SPEED Pages: 19

Brand: Kuda-Phonebase Pages: 3

Brand: Wilco Offroad Pages: 4

Brand: Renault Pages: 238

Brand: B-Speech Pages: 4

Brand: Kuda Pages: 3

Brand: Webasto Pages: 18

Brand: Ford Pages: 256

Brand: Hella Pages: 21

Brand: SCC Pages: 4

Brand: Brodit Pages: 2

RearSight 250-8308

Brand: Rostra Pages: 2

Brand: Brink Pages: 21

Brand: Ford Pages: 4378

Brand: Toyota Pages: 549

Brand: Tesla Pages: 42

Brand: Nos Pages: 22

Cuda TriOptic 351014F Series

Brand: Federal Signal Corporation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands