Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 23 | Manualshive

Page: 23 / 147

background image

CONSOLE AND SWITCHES

q

Turn Signal Lever; Cruise Control

Switches; Headlight High/Low Beam Switch

w

Instrument Cluster

e

Ignition Switch

r

Horn Button

HORN

Press the horn button to sound the horn. The ignition switch must be in the ON
position.

IGNITION SWITCH

The ignition key operates the ignition switch, glove box lock and storage
compartment locks (behind seats). Read the engine starting procedures
beginning on page 55 before starting the engine. Store the spare key in a safe
place separate from the main key.

Place the ignition key in the ignition switch to operate the following functions of
the switch.

OFF

All electrical circuits are off. Hazard signals can be activated. The key can be
removed.

ON

All electrical circuits are on. The ignition key cannot be removed. Headlight,
taillight, running lights, turn signals, horn, radio and instrument lights are
powered.

ACC

Power is supplied to accessory circuits, radio, instruments and hazard signals.
The key can be removed.

21

FEATURES AND CONTROLS

Downloaded from

«
...
21
22
23
24
25
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: JANE Pages: 6

Brand: Vauxhall Pages: 2

Brand: Audi Pages: 12

Brand: Opel Pages: 32

Brand: Quadratec Pages: 6

Brand: Rugged Ridge Pages: 3

Brand: SNIPER Pages: 2

Brand: Gator Pages: 6

Brand: Cadillac Pages: 335

Brand: Toyota Pages: 295

Brand: Cadillac Pages: 438

Brand: CITROEN Pages: 394

Brand: Gator Pages: 5

Brand: Rosco Pages: 12

Brand: Cadillac Pages: 508

Brand: Kia Pages: 289

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands