Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 147

background image

FEATURES AND CONTROLS

IGNITION KEY NUMBER

The ignition key number is stamped on the small metal tag attached to the key
ring.

Remove

the tag and record the number on page 7. Store the tag in a safe

place.

Additional keys can be copied from one of the original keys. A key blank from
your dealer is required. If you lose both original keys, you will need the following:

•  Key number (recorded on page 7)
•  A new key blank from your dealer
•  Proof of ownership
•  A locksmith or dealer with the equipment necessary to cut a new key

ENGINE IDENTIFICATION NUMBER

The engine identification number

q

is stamped on a pad on the oil filter bowl.

The number is also provided on labels located on the front and rear of the cam
cover

w

. Record the number in the space provided on page 7.

19

FEATURES AND CONTROLS

Downloaded from

«
...
19
20
21
22
23
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Ranger design Pages: 6

Brand: Yakima Pages: 8

Brand: Paxton Automotive Pages: 85

Brand: Thule Pages: 8

Brand: Ford Pages: 22

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: Whelen Engineering Company Pages: 9

Brand: rockymounts Pages: 6

Brand: Paccar Pages: 63

Brand: r.LiNK Pages: 20

Brand: Fiat Pages: 284

Brand: Chevrolet Pages: 46

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Brand: Ecco Pages: 2

10.297.300K-303K

Brand: AUTOTECH Pages: 1

Brand: MovaNext Pages: 4

Brand: Yakima Pages: 10

Brand: Rajant Pages: 11

Brand: Technaxx Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands